We wanted to have something new to tinker with for some time – now we can start. Old and new are coming together in our new project called „Mäcki“. Among other things, we have acquired a new chassis and a new reservoir.
We have already made trial run with the most important components. We wanted to see at the beginning, if everything fits as we imagined it or if there were any problems. Here is a glimpse at our chassis:
The hardware is perfectly suited for what we are going to do after everything is assembled. You find a complete list of all components at the end of the post. We want to mount the aquaero on the bottom of the upper ventilation grid. Since the four screws of the board unfortunately do not fit the structure of the holes of the grid, we have already commissioned a small metal plate. In the picture below, we have placed the aquaero on top to find the best spot to mount it.
Here are two more impressions from the combination of reservoir and pump:
In any case, the PCB of the GPU should not be longer as it is:
Computer Hardware (26. Mai 2017) Chassis: Fractal Design Define S Window Motherboard: Gigabyte Z97N-WiFi CPU: Intel i7 4790K RAM: Kingston HyperX Beast, 2400MHz, 16 GB GPU: EVGA GTX 780 Ti SC PSU: Enermax Platimax 1200 W SSD: Samsung 850 Pro 512 GB (2x)
WaKü-Hardware (26. Mai 2017) CPU waterblock: Watercool Heatkiller IV Pro Copper-Nickel GPU waterblock: Watercool Heatkiller GPU-X GTX 780Ti „Acryl Edition“ Radiator Top: Alphacool NexXxoS ST30 Full Copper 240mm Radiator Front: Alphacool NexXxoS UT60 Full Copper 360mm Reservoir: Watercool Heatkiller Tube 200 DDC Pump: Laing DDC 12V DDC-1T Plus Tube: Masterkleer 16/10mm Liquid: tdb Controller (fans and pump): Aquacomputer aquaero 6 XT Fittings: Aquatuning Perfect Seal / 90 degree revolvable Flow meter: tbd Temperatur sensor: tbd fans: tbd
For the installation of the aquaero, we had announced that we wanted to use a small metal plate. We picked it up from the metal workshop just before the weekend. It is mounted at the top of the chassis, directly next to the small 240-radiator.
This is a view from above:
The plate has 8 holes, the outer four with screw threads:
On the back of the chassis, we had these 4 holes drilled.
The aluminum plate is to be painted black, so we had to grind it down yesterday …
Here we are with a brief update on our project. Since our last post, we ground the metal plate and sprayed it with base coat a second time. A couple of days ago, we also applied the first layer of black color. (Please excuse the poor image quality.)
The motherboard (Gigabyte Z97N-WiFi) was part of our „Red Devil“ system, which is no longer in use. It was also watercooled. We have begun to replace the old waterblock for the processor – a Watercool Heatkiller III – with the current Heatkiller IV.
This is a view of the copper plate of the Heatkiller III:
Next time, we will continue with the mounting of the Heatkiller IV on the motherboard.
In the last post we had already begun to detach the „old“ CPU Heatkiller III from the motherboard. Now we started to install the new CPU Heatkiller IV.
We began with removing the rest of the thermal compound on the CPU.
The back plate belongs on the backside of the motherboard.
All necessary screws and bolts are included in the shipment of the Heatkiller IV.
Here, the four so-called „studs“ are screwed in. They are part of the „EasyMount System“ from Watercool. Everything is described in detail in the assembly instructions for the Heatkiller IV.
After that, the new thermal compound is carefully applied…
…and spread evenly.
Here, our installation of the Heatkiller IV is completed. It was thoroughly cleaned and rinsed with distilled water beforehand. To protect it from any dust, we used two caps.
As far as the orientation of the waterblock is concerned, we would have preferred to have the OUT port facing right. This would have made the tubing a bit easier. But when mounted this way, the waterblock touches the small capacitors on the left side of the socket.